P retty hello card using Stampin' Up! products.
Project Recipe
Cut cardstock pieces to the following sizes using a Paper Trimmer:
- card from Starry Sky Cardstock at 5-1/2" x 8-1/2" and scored at 4-1/4"
- 4" x 5-1/4" from Basic White Cardstock
- 2-1/2" x 4-3/4" from Basic White Cardstock
- 2-3/4" x 3-1/4" from Basic White Cardstock
- 1-1/2" x 4-1/4" from Soft Succulent Cardstock
- 1-1/4" square from Starry Sky Cardstock
Place the 4" x 5-1/4" white cardstock on some Grid Paper to protect your work surface.
Mount the large spray of leaves and berries image from the Eden's Garden Set on Block D. Ink it up with the Soft Succulent Ink Pad. Stamp it all over the white rectangle. Remember to re-ink the stamp each time. Let some of the images go off the edges of the cardstock. Change the orientation of the stamp a little each time. Leave the stamp on the block.
Re-ink the large spray of leaves and berries image on Block D with the Soft Succulent Ink Pad. Stamp it in the center of the 2-3/4" x 3-1/4" white rectangle.
Adhere the stamped 4" x 5-1/4" white rectangle to the front of the Starry Sky card.
Cut a 5-1/2" piece of the Soft Succulent 1/2" Satin Shimmer Ribbon so it has a sharp angle on each end.
Adhere a 4" strip of Tear & Tape Adhesive horizontally down the center of the horizontal card front. Remove the protective backing and adhere the ribbon horizontally to the Tear & Tape.
Use Paper Snips Scissors to cut out the previously stamped large spray of leaves and berries by hand.
Use Stampin' Dimensionals to adhere the cut out large spray of leaves and berries to the front of the card so it is centered over the ribbon.
Pick out the long, skinny label with leafy ends die from the Eden Dies. Put it on top of the Soft Succulent strip on a platform on your Stampin' Cut & Emboss Machine. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
Mount the "Hello There" sentiment from the Eden's Garden Set on Block G. Ink it up with the Starry Sky Ink Pad. Stamp it in the center of the leafy ended label cut out.
Adhere the stamped leafy ended label cut out to the front of the card so it is centered over the large spray of leaves and berries cut out.
Pick out the long, skinny flower swag die from the Flowers Of Home Dies. Put it on top of one side of the remaining white cardstock on a platform on your Stampin' Cut & Emboss Machine. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces. Repeat on the other side of the white cardstock so you have two swags cut out.
Put the cut out swags on some Grid Paper to protect your work surface. Use the brush tips of the Soft Succulent and Starry Sky Stampin' Write Markers to color the leaves and flowers on the swag cut outs.
Use Multipurpose Liquid Glue or Fine-Tip Glue Pen to adhere the colored swag cut outs to the front of the card so they are centered side to side and are just above and below the large spray of leaves and berries cut out in the center of the card.
Pick out the set of three little flowers die from the Flowers Of Home Dies. Put it on top of the Starry Sky square on a platform on your Stampin' Cut & Emboss Machine. Run through the machine. Use the paper-piercing tool on the Take Your Pick to remove the pieces.
Use the Multipurpose Liquid Glue or Fine-Tip Glue Pen to adhere the two smaller flower cut outs to the top of the large spray of leaves and berries cut out above and below the sentiment label cut out as shown.
Use the Multipurpose Liquid Glue or Fine-Tip Glue Pen to adhere the larger flower cut out to the card front so it is just tucked under the upper left side of the large spray of leaves and berries cut out as shown.
Use the mini spatula on the Take Your Pick to carefully peel up 1 large and 2 small Starry Sky dots from the sheet of 2022-2024 In Color Matte Decorative Dots making sure that you get the adhesive backings as well. Adhere them to the centers of the flower cut outs as shown.